ADS5282 Eight-Channel; 12-Bit; 65-MSPS Analog-to-Digital Converter Evaluation Module

EVAL MODULE FOR TPS65055-258

KIT EVALUATION FOR MSP430X32X

DEM-OPA-SO-1E

The AD7293 is a PA drain current controller containing functionality for general-purpose monitoring and control of current, voltage, and temperature, integrated into a single chip solution with an SPI-compatible interface.The device features a 4-channel, 12-bit successive approximation register (SAR) ADC, eight 12-bit DACs (four bipolar and four unipolar with output ranges that can be configured to shut down under external pin control), a ?1.25?C accurate internal temperature sensor, and eight general-purpose input/output (GPIO) pins.The device also includes limit registers for alert functions and four high-side current sense amplifiers to measure current across external shunt resistors. These amplifiers can be optionally set to operate as part of four independent closed-loop drain current controllers.A high accuracy 2.5 V internal reference is provided to drive theDACs and the ADC. The 12-bit ADC monitors and digitizes theinternal temperature sensor, and two inputs are included for theexternal diode temperature sensors.Product Highlights Four independent closed-loop drain current controllers. Built-in monitoring, sequencing, and alert features. Compatible with both depletion mode and enhancement mode power amplifiers.Applications GaN and GaAs power amplifier monitoring and controls Base station power amplifiers General-purpose system monitoring and controls

The AD7329 is an 8-Channel, 12-Bit Plus Sign Successive Approximation ADC. The ADC has a high-speed serial interface that can operate at throughput rates up to 1 MSPS. The ADC has a high-speed serial interface that can operate at throughput rates up to 250 kSPS.The AD7329 can accept True Bipolar Analog input signals. The Ad7329 has four software selectable ranges, ?10 V, ?5 V, ?2.5 V and 0 to 10 V. Each analog input channel can be independently programmed to one of the input ranges by setting the appropriate bits in the Range Registers.The Analog Input Channels can be configured as single ended, fully differential or pseudo differential. Dedicated Control Register bits are used to configure the Analog inputs.The ADC contains a 2.5 V Internal reference. The AD7329 also allows for external Reference operation. If a 3 V external reference is applied to the REFIN/OUT pin, the ADC can handle a True Bipolar ? 12 V Analog input range. VDD and VSS supplies of ? 12 V are required for this ? 12 V input range.The AD7329 has multiplexer output pins and ADC input pins. These allow the user to insert buffers, differential amplifiers or antialiasing filters, if required, between the Multiplexer and the ADC. This means that for eight analog inputs only a single driver is required for the AD7329.The AD7329 has a number of power down mode to reduce power consumption at lower throughput rates.PRODUCT HIGHLIGHTS The AD7329 can accept True Bipolar Analog Input signals, ?10V, ?5V, ?2.5V and 0 to 10V unipolar signals. The Eight Analog Inputs can be configured as 8 Single-Ended inputs, 4 True Differential, 4 Pseudo Differential or 7 Pseudo Differential Inputs. SPI/QSPI/DSP/MICROWIRE compatible Interface. Low Power, TBD mW at maximum throughput rate. Channel Sequencer

The AD7366?/ AD7367 are dual 12-bit/14-bit, high speed, low power, successive approximation analog-to-digital converters (ADCs) that feature throughput rates up to 1 MSPS. The device contains two ADCs, each preceded by a 2-channel multiplexer, and a low noise, wide bandwidth track-and-hold amplifier.The AD7366 / AD7367 are fabricated on the Analog Devices, Inc., industrial CMOS process (iCMOS), which is a technology platform combining the advantages of low and high voltage CMOS. The iCMOS process allows the AD7366 / AD7367 to accept high voltage bipolar signals in addition to reducing power consumption and package size. The AD7366 / AD7367 can accept true bipolar analog input signals in the ?10 V range, ?5 V range, and 0 V to 10 V range.The AD7366 / AD7367 have an on-chip 2.5 V reference that can be disabled to allow the use of an external reference. If a 3 V reference is applied to the DCAPA and DCAPB pins, the AD7366 / AD7367 can accept a true bipolar ?12 V analog input. Minimum ?12 V VDD and VSS supplies are required for the ?12 V input range.PRODUCT HIGHLIGHTS The AD7366 / AD7367 can accept true bipolar analog input signals, as well as ?10 V, ?5 V, ?12 V (with external reference), and 0 V to 10 V unipolar signals. Two complete ADC functions allow simultaneous sampling and conversion of two channels. 1 MSPS serial interface: SPI-/QSPI-/DSP-/MICROWIRE-compatible interface.

The 16-bit AD7383 and the 14-bit AD7384 are a pin-compatible family of dual simultaneous sampling, high speed, low power, successive approximation register (SAR), analog-to-digital converters (ADCs) that operate from a 3.0 V to 3.6 V power supply and feature throughput rates up to 4 MSPS. The analog input type is pseudo differential and is sampled and converted on the falling edge of CS.Integrated on-chip oversampling blocks improve dynamic range and reduce noise at lower bandwidths. A buffered internal 2.5 V reference is included. Alternatively, an external reference up to 3.3 V can be used.The conversion process and data acquisition use standard control inputs that allow simple interfacing to microprocessors or digital signal processors (DSPs). The devices are compatible with 1.8 V, 2.5 V, and 3.3 V interfaces, using a separate logic supply.The AD7383 and the AD7384 are available in a 16-lead lead frame chip scale package (LFCSP) with operation specified from ?40?C to +125?C.Multifunction pin names may be referenced by their relevant function only.PRODUCT HIGHLIGHTS Dual simultaneous sampling and conversion with two complete ADC functions. Pin-compatible product family. High 4 MSPS throughput rate. Space saving 3 mm ? 3 mm LFCSP. Integrated oversampling block to increase dynamic range, reduce noise, and reduce SCLK speed requirements. Pseudo differential analog inputs. Small sampling capacitor reduces amplifier drive burden.APPLICATIONS Motor control position feedback Motor control current sense Sonar Power quality Data acquisition systems Erbium doped fiber amplifier (EDFA) applications I and Q demodulation

The AD7386/AD7387/AD7388 are 16-bit, 14-bit, and 12-bit dual, simultaneous sampling, high speed, successive approximation register (SAR), analog-to-digital converters (ADCs) that operate from a 3.0 V to 3.6 V power supply and feature throughput rates of up to 4 MSPS. The analog input types are single-ended and are sampled and converted on the falling edge of CS.The AD7386/AD7387/AD7388 have an on-chip sequencer and integrated on-chip oversampling block to improve dynamic range and reduce noise at lower bandwidths. Abuffered internal 2.5 V reference is included. Alternatively, an external reference up to 3.3 V can be used. The conversion process and data acquisition use standard control inputs, allowing interfacing to microprocessors or digital signal processors (DSPs). The AD7386 is compatible with 1.8 V, 2.5 V, and 3.3 V interfaces by using the separate logic supply.The AD7386/AD7387/AD7388 are available in a 16-lead LFCSP with operation specified from ?40?C to +125?C.Product Highlights 4-channel, dual simultaneous sampling ADC. Pin-compatible product family. High 4 MSPS throughput rate. Space-saving 3 mm ? 3 mm LFCSP. Integrated oversampling block to increase dynamic range and SNR and to reduce SCLK speed requirements. Single-ended analog inputs. Small sampling capacitor reduces amplifier drive burden.Applications Motor control position feedback Motor control current sense Sonar Power quality Data acquisition systems Erbium doped fiber amplifier (EDFA) applications Inphase and quadrature demodulation

The AD7400A is a second-order, ?-? modulator that converts an analog input signal into a high speed, 1-bit data stream with on-chip digital isolation based on Analog Devices, Inc., iCoupler? technology. The AD7400A operates from a 5 V power supply and accepts a differential input signal of ?250 mV (?320 mV full scale). The analog input is sampled continuously by the analog modulator, eliminating the need for external sample-and-hold circuitry. The input information is contained in the output stream as a density of ones with a data rate of 10 MHz. The original information can be reconstructed with an appropriate digital filter. The serial I/O can use a 5 V or a 3 V supply (VDD2).The serial interface is digitally isolated. High speed CMOS, combined with monolithic air core transformer technology, means the on-chip isolation provides outstanding performance characteristics superior to alternatives such as optocoupler devices. The part contains an on-chip reference and has an operating temperature range of ?40?C to +125?C. The AD7400A is offered in an 8-lead surface-mount PDIP with gull wing leads and a 16-lead SOIC package.APPLICATIONS AC motor controls Shunt current monitoring Data acquisition systems Analog-to-digital and opto-isolator replacements