3000 V/S, 35mW Current Feedback Quad Amplifier Features: High speed 250 MHz -3 dB bandwidth (G = +1) 3000 V/µs slew rate 21 ns settling time to 0.1% 1.8 ns rise time for 2 V step Low power 3.5 mA/amp power supply Current (35 mW/amp) Single supply operation Fully specified for +5 V supply High output current of 50 mA Good video specifications (RL = 150 Ω, G = +2) Gain flatness 0.1 dB to 30 MHz 0.04% differential gain error 0.10° differential phase error Low distortion –78 dBc THD at 5 MHz –61 dBc THD at 20 MHz Available in a 14-lead SOIC

160 MHz Rail-to-Rail Amplifier with Disable Features: Fully specified for +3 V, +5 V and ±5 V Supplies Output Swings Rail to Rail Input Voltage Range Extends 200 mV Below Ground No Phase Reversal with Inputs 1 V Beyond Supplies Disable/Power-Down Capability Low Power of 5.2 mA (26 mW on 5 V) High Speed and Fast Settling on 5 V: 160 MHz -3 dB Bandwidth (G = +2) 160 V/µs Slew Rate 30 ns Settling Time to 0.1% Good Video Specifications (RL = 150 Ω, G = +2) Gain Flatness of 0.1 dB to 30 MHz 0.03% Differential Gain Error 0.03° Differential Phase Error Low Distortion -69 dBc Worst Harmonic @ 10 MHz Outstanding Load Drive Capability Drives 50 mA 0.5 V from Supply Rails Cap Load Drive of 45 pF

Triple Differential Receiver with Adjustable Line Equalization Features: Compensates cables to 300 meters for wideband video Fast rise and fall times 4.9 ns with 2 V step at 150 meters of UTP cable 8.0 ns with 2 V step at 300 meters of UTP cable 55 dB peak gain at 100 MHz Two frequency response gain adjustment pins High frequency peaking adjustment (VPEAK) Broadband flat gain adjustment (VGAIN) Pole location adjustment pin (VPOLE) Compensates for variations between cables Can be optimized for either UTP or coaxial cable DC output offset adjust (VOFFSET) Low output offset voltage: 24 mV Compensates both RGB and YPbPr Two on-chip comparators with hysteresis Can be used for common-mode sync extraction Available in 40-lead, 6 mm × 6 mm LFCSP

Low Cost 270 MHz Differential Receiver Amplifier Features: High Speed AD8130: 270 MHz, 1090 V/µs @ G = +1 AD8129: 200 MHz, 1060 V/µs @ G = +10 High CMRR 94 dB min, dc to 100 kHz 80 dB min @ 2 MHz 70 dB @ 10 MHz Low noise AD8130: 12.5 nV/√Hz AD8129: 4.5 nV/√Hz High input impedance: 1 MΩ differential Input common-mode range ±10.5 V Low distortion, 1 V p-p @ 5 MHz: AD8130, -79 dBc worst harmonic @ 5 MHz AD8129, -74 dBc worst harmonic @ 5 MHz User-adjustable gain No external components for G = +1 Power supply range +4.5 V to ±12.6 V Power-down

Triple Differential Driver for Wideband Video Features:Triple high speed fully differential driver700 MHz, 3 dB, 2 V p-p bandwidth (AD8146/AD8148)600 MHz, 3 dB, 2 V p-p bandwidth (AD8147)200 MHz, 0.1 dB, 2 V p-p bandwidth3000 V/s slew rate Fixed gain (AD8146/AD8147: G = 2, AD8148: G = 4) Differential or single-ended input to differential output Can be used as differential-to-differential receiver Drives one or two 100 UTP cables Adjustable output common-mode voltage (AD8146) Internal common-mode feedback network Output balance error 50 dB @ 50 MHz On-chip, sync-on common-mode encoding (AD8147/AD8148) Output pull-down feature for line isolation Low power: 57 mA @ 5 V for 3 drivers (AD8146) Wide supply voltage range: +5 V to 5 V Available in a small 4 mm 4 mm LFCSP

Low Cost JFET Input Operational Amplifier Features: TL082/TL084 compatible Low input bias current: 10 pA maximum Offset voltage 5.5 mV maximum (ADTL082A/ADTL084A) 9 mV maximum (ADTL082J/ADTL084J) ±15 V operation Low noise: 16 nV/√Hz Wide bandwidth: 5 MHz Slew rate: 20 V/μs CMRR: 80 dB minimum Total harmonic distortion: 0.001% Supply current: 1.2 mA typical Unity-gain stable

2.5kV rms Isolated Error Amplifier Features: Stability in isolated feedback applications 0.5% initial accuracy 1% accuracy over the full temperature range Compatible with Type II or Type III compensation networks Reference voltage: 1.225 V Compatible with DOSA Low power operation: <7 mA total Wide voltage supply range VDD1: 3 V to 20 V VDD2: 3 V to 20 V Bandwidth: 400 kHz Isolation voltage: 2.5 kV rms Safety and regulatory approvals UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 565 V peak Wide temperature range −40°C to +125°C ambient operation 150°C maximum junction temperature Qualified for automotive applications

Precision, Low Power Rail-to-Rail Input/Output Differential Op Amp/SAR ADC Driver Features: 1mA Supply Current Single 2.8V to 5.25V supply Fully Differential Input and Output 200μV Max Offset Voltage 260nA Max Input Bias Current Fast Settling: 550ns to 18-Bit, 8VP-P Output Low Distortion: –116dBc at 1kHz, 8VP-P Rail-to-Rail Inputs and Outputs 3.9nV/√Hz Input-Referred Noise 180MHz Gain-Bandwidth Product 34MHz –3dB Bandwidth Low Power Shutdown: 70μA 8-Lead MSOP and 3mm × 3mm 8-Lead DFN Packages

Low Power, Low Noise and Distortion, Rail-to-Rail Output Amplifier Features: Low power: 1.1 mA/amp Low wideband noise 2.1 nV/√Hz 1.4 pA/√Hz Low 1/f noise 7 nV/√Hz @ 10 Hz 13 pA/√Hz @ 10 Hz Low distortion: −105 dBc @ 100 kHz, VO = 2 V p-p High speed 80 MHz, −3 dB bandwidth (G = +1) 12 V/μs slew rate 175 ns settling time to 0.1% Low offset voltage: 0.3 mV maximum Rail-to-rail output Power down Wide supply range: 2.7 V to 12 V

Low Noise Single-Ended to Differential Converter/ADC Driver Features: Rail-to-Rail Input and Outputs Fast Settling Time: 240ns, 0.01%, 8VP-P Output Step 1.9nV/√Hz Input-Referred Op Amp Noise High Impedance Input –3dB Bandwidth: 33MHz 2.7V to 12V Supply Operation No External Gain Resistors Required 4.8mA Supply Current Low Power Shutdown Low Distortion (HD2/HD3): –102dBc/–97dBc at 100kHz, VOUTDIFF = 4VP-P Low Offset Voltage: ±400μV Max High DC Linearity: <±1LSB, 16-Bit, 8VP-P Low Input Current Noise: 1.1pA/√Hz 3mm × 3mm 8-Pin DFN and 8-Lead MSOP Packages