The LT3469 is a transconductance (gm) amplifier that can drive outputs up to 33V from a 5V or 12V supply. An internal switching regulator generates a boosted supply voltage for the gm amplifier. The amplifier can drive capacitive loads in the range of 5nF to 300nF. Slew rate is limited only by the maximum output current. The 35V output voltage capability of the switching regulator, along with the high supply voltage of the amplifier, combine to allow the wide output voltage range needed to drive a piezoceramic microactuator.The LT3469 switching regulator switches at 1.3MHz, allowing the use of tiny external components. The output capacitor can be as small as 0.22?F, saving space and cost versus alternative solutions.The LT3469 is available in a low profile ThinSOT? package.Applications Piezo Speakers Piezo Microactuators Varactor Bias

The ADCMP551 / ADCMP552?/ ADCMP553?are single supply,high speed comparators fabricated on Analog Devices?proprietary XFCB process. The devices feature a 750 ps propagation delay with less than 150 ps overdrive dispersion. Dispersion, a measure of the difference in propagation delay under differing overdrive conditions, is a particularly importantcharacteristic of high speed comparators. A separateprogrammable hysteresis pin is available on the ADCMP552.A differential input stage permits consistent propagation delay with a common-mode range from ?0.2 V to VCCI ? 2.0 V. Outputs are complementary digital signals are fully compatible with PECL 10 K and 10 KH logic families. The outputs providesufficient drive current to directly drive transmission lines terminated in 50 ? to VCCO - 2 V. A latch input is included and permits tracking, track-and-hold, or sample-and-hold modes of operation. The latch input pins contain internal pullups that set the latch in tracking mode when left open. The ADCMP551 / ADCMP552 / ADCMP553 are specified over the ?40?C to +85?C industrial temperature range. TheADCMP551 is available in a 16-lead QSOP package; theADCMP552 is available in a 20-lead QSOP package; and the ADCMP553 is available in an 8-lead MSOP package.APPLICATIONS Automatic test equipment High speed instrumentation Scope and logic analyzer front ends Window comparators High speed line receivers Threshold detection Peak detection High speed triggers Patient diagnostics Disk drive read channel detection Hand-held test instruments Zero crossing detectors Line receivers and signal restoration Clock drivers

The ADCMP563/ADCMP564 are high speed comparatorsfabricated on Analog Devices? proprietary XFCB process. Thedevices feature a 700 ps propagation delay with less than 75 psoverdrive dispersion. Dispersion, a measure of the difference inpropagation delay under differing overdrive conditions, is a particularlyimportant characteristic of high speed comparators. A separateprogrammable hysteresis pin is available on the ADCMP564.A differential input stage permits consistent propagation delaywith a wide variety of signals in the common-mode range from?2.0 V to +3.0 V. Outputs are complementary digital signals thatare fully compatible with ECL 10 K and 10 KH logic families.The outputs provide sufficient drive current to directly drivetransmission lines terminated in 50 ? to ?2 V. A latch input,which is included, permits tracking, track-and-hold, or sample-and-holdmodes of operation. The latch input pins contain internalpull-ups that set the latch in tracking mode when left open.The ADCMP563/ADCMP564 are specified over the industrialtemperature range (?40?C to +85?C).Applications Automatic test equipment High speed instrumentation Scope and logic analyzer front ends Window comparators High speed line receivers Threshold detection Peak detection High speed triggers Patient diagnostics Hand-held test instruments Zero crossing detectors Line receivers and signal restoration Clock drivers

The ADCMP580/ADCMP581/ADCMP582 are ultrafast voltagecomparators fabricated on the Analog Devices, Inc. proprietaryXFCB3 Silicon Germanium (SiGe) bipolar process. TheADCMP580 features CML output drivers, the ADCMP581features reduced swing ECL (negative ECL) output drivers, andthe ADCMP582 features reduced swing PECL (positive ECL)output drivers.All three comparators offer 180 ps propagation delay and 100 psminimum pulse width for 10 Gbps operation with 200 fs randomjitter (RJ). Overdrive and slew rate dispersion are typically lessthan 15 ps.The ?5 V power supplies enable a wide ?2 V to +3 V inputrange with logic levels referenced to the CML/NECL/PECLoutputs. The inputs have 50 ? on-chip termination resistorswith the optional capability to be left open (on an individualpin basis) for applications requiring high impedance input. The CML output stage is designed to directly drive 400 mV into50 ? transmission lines terminated to ground. The NECL outputstages are designed to directly drive 400 mV into 50 ? terminatedto ?2 V. The PECL output stages are designed to directly drive400 mV into 50 ? terminated to VCCO ? 2 V. High speed latchand programmable hysteresis are also provided. The differentiallatch input controls are also 50 ? terminated to an independentVTT pin to interface to either CML or ECL or to PECL logic.The ADCMP580/ADCMP581/ADCMP582 are available in a16-lead LFCSP.Applications Automatic test equipment (ATE) High speed instrumentation Pulse spectroscopy Medical imaging and diagnostics High speed line receivers Threshold detection Peak and zero-crossing detectors High speed trigger circuitry Clock and data signal restoration

The ADCMP600, ADCMP601, and ADCMP602 are very fast comparators fabricated on Analog Devices? proprietary XFCB2 process. These comparators are exceptionally versatile and easy to use. Features include an input range from ? 0.5 V to VCC + 0.2 V, low noise TTL-/CMOS-compatible output drivers, and latch inputs with adjustable hysteresis and/or shutdown inputs.The devices offer 5 ns propagation delay with 10 mV overdrive on 3 mA typical supply current.A flexible power supply scheme allows the devices to operate with a single +2.5 V positive supply and a ?0.5 V to +2.8 V input signal range up to a +5.5 V positive supply with a ?0.5 V to +5.8 V input signal range. Split input/output supplies with no sequencing restrictions on the ADCMP602 support a wide input signal range while still allowing independent output swing control and power savings.The TTL-/CMOS-compatible output stage is designed to drive up to 5 pF with full timing specs and to degrade in a graceful and linear fashion as additional capacitance is added. The comparator input stage offers robust protection against large input overdrive, and the outputs do not phase reverse when the valid input signal range is exceeded. High speed latch and programmable hysteresis features are also provided with a unique single-pin control option.The ADCMP600 is available in both 5-lead SC70 and SOT-23 packages, the ADCMP601 is available in a 6-lead SC70 package, and the ADCMP602 is available in 8-lead MSOP and LSCFP packages.Applications High Speed Instrumentation Clock and Data Signal Restoration Logic Level Shifting or Translation Pulse Spectroscopy High Speed Line Receivers Threshold Detection Peak and Zero-crossing Detectors High Speed Trigger Circuitry Pulse-width Modulators Current-/voltage-controlled Oscillators Automatic Test Equipment (ATE)

The ADCMP600, ADCMP601, and ADCMP602 are very fast comparators fabricated on Analog Devices? proprietary XFCB2 process. These comparators are exceptionally versatile and easy to use. Features include an input range from ? 0.5 V to VCC + 0.2 V, low noise TTL-/CMOS-compatible output drivers, and latch inputs with adjustable hysteresis and/or shutdown inputs.The devices offer 5 ns propagation delay with 10 mV overdrive on 3 mA typical supply current.A flexible power supply scheme allows the devices to operate with a single +2.5 V positive supply and a ?0.5 V to +2.8 V input signal range up to a +5.5 V positive supply with a ?0.5 V to +5.8 V input signal range. Split input/output supplies with no sequencing restrictions on the ADCMP602 support a wide input signal range while still allowing independent output swing control and power savings.The TTL-/CMOS-compatible output stage is designed to drive up to 5 pF with full timing specs and to degrade in a graceful and linear fashion as additional capacitance is added. The comparator input stage offers robust protection against large input overdrive, and the outputs do not phase reverse when the valid input signal range is exceeded. High speed latch and programmable hysteresis features are also provided with a unique single-pin control option.The ADCMP600 is available in both 5-lead SC70 and SOT-23 packages, the ADCMP601 is available in a 6-lead SC70 package, and the ADCMP602 is available in 8-lead MSOP and LSCFP packages.Applications High Speed Instrumentation Clock and Data Signal Restoration Logic Level Shifting or Translation Pulse Spectroscopy High Speed Line Receivers Threshold Detection Peak and Zero-crossing Detectors High Speed Trigger Circuitry Pulse-width Modulators Current-/voltage-controlled Oscillators Automatic Test Equipment (ATE)

The ADCMP604 / ADCMP605?are very fast comparators fabricated on the Analog Devices, Inc. proprietary XFCB2 process. These comparators are exceptionally versatile and easy to use. Features include an input range from VEE ? 0.5 V to VCCI + 0.2 V, low noise, LVDS-compatible output drivers, and TTL/CMOS latch inputs with adjustable hysteresis and/or shut-down inputs.The devices offer 1.5 ns propagation delays with 1 ps rms random jitter (RJ). Overdrive and slew rate dispersion are typically less than 50 ps.A flexible power supply scheme allows the devices to operate with a single 2.5 V positive supply and a ?0.5 V to +2.7 V input signal range up to a 5.5 V positive supply with a ?0.5 V to +5.7 V input signal range. Split input/output supplies, with no sequencing restrictions on the ADCMP605, support a wide input signal range with greatly reduced power consumption.The LVDS-compatible output stage is designed to drive any standard LVDS input. The comparator input stage offers robust protection against large input overdrive, and the outputs do not phase reverse when the valid input signal range is exceeded. High speed latch and programmable hysteresis features are also provided in a unique single-pin control option.The ADCMP604 is available in a 6-lead SC70 package, and the ADCMP605 is available in a 12-lead LFCSP.APPLICATIONS High speed instrumentation Clock and data signal restoration Logic level shifting or translation Pulse spectroscopy High speed line receivers Threshold detection Peak and zero-crossing detectors High speed trigger circuitry Pulse-width modulators Current-/voltage-controlled oscillators Automatic test equipment (ATE)

The LTC2051/LTC2052 are dual/quad zero-drift operational amplifiers available in the MS8 and SO-8/GN16 and S14 packages. For space limited applications, the LTC2051 is available in a 3mm ? 3mm ? 0.8mm dual fine pitch leadless package (DFN). They operate from a single 2.7V supply and support ?5V applications. The current consumption is 750?A per op amp.The LTC2051/LTC2052, despite their miniature size, feature uncompromising DC performance. The typical input offset voltage and offset drift are 0.5?V and 10nV/?C. The almost zero DC offset and drift are supported with a power supply rejection ratio (PSRR) and common mode rejection ratio (CMRR) of more than 130dB.The input common mode voltage ranges from the negative supply up to typically 1V from the positive supply. The LTC2051/LTC2052 also have an enhanced output stage capable of driving loads as low as 2k? to both supply rails. The open-loop gain is typically 140dB. The LTC2051/ LTC2052 also feature a 1.5?VP-P DC to 10Hz noise and a 3MHz gain-bandwidth product.Applications Thermocouple Amplifiers Electronic Scales Medical Instrumentation Strain Gauge Amplifiers High Resolution Data Acquisition DC Accurate RC Active Filters Low Side Current Sense

The LTC6268/LTC6269 is a single/dual 500MHz FET-input operational amplifier with extremely low input bias current and low input capacitance. It also features low input-referred current noise and voltage noise making it an ideal choice for high speed transimpedance amplifiers, CCD output buffers, and high-impedance sensor amplifiers. Its low distortion makes the LTC6268/LTC6269 an ideal amplifier for driving SAR ADCs.It operates on 3.1V to 5.25V supply and consumes 16.5mA per amplifier. A shutdown feature can be used to lower power consumption when the amplifier is not in use.The LTC6268 single op amp is available in 8-lead SOIC and 6-lead SOT-23 packages. The SOIC package includes two unconnected pins which can be used to create an input pin guard ring to protect against board leakage currents. The LTC6269 dual op amp is available in 8-lead MSOP with exposed pad and 3mm ? 3mm 10-lead DFN packages. They are fully specified over the ?40?C to 85?C and the ?40?C to 125?C temperature ranges.Applications Trans-Impedance Amplifiers ADC Drivers CCD Output Buffer Photomultiplier Tube Post-Amplifier Low IBIAS Circuits

The LT6375 is a unity-gain difference amplifier which combines excellent DC precision, a very high input common mode range and a wide supply voltage range. It includes a precision op amp and a highly-matched thin film resistor network. It features excellent CMRR, extremely low gain error and extremely low gain drift.Comparing the LT6375 to existing difference amplifiers with high common mode voltage range, the selectable resistor divider ratios of the LT6375 offer superior system performance by allowing the user to achieve maximum SNR, precision and speed for a specific input common mode voltage range.The op amp at the core of the LT6375 has Over-The-Top? protected inputs which allow for robust operation in environments with unpredictable voltage conditions. See the Applications Information section for more details.The LT6375 is specified over the ?40?C to 125?C temperature range and is available in space-saving MSOP16 and DFN14 packages.Applications High Side or Low Side Current Sensing Bidirectional Wide Common Mode Range Current Sensing High Voltage to Low Voltage Level Translation Precision Difference Amplifier Industrial Data-Acquisition Front-Ends Replacement for Isolation Circuits