The MAX1874 charges a single-cell Li+ battery from both USB and AC adapter sources. It also includes battery-to-input power switchover, so the system can be powered directly from the power source rather than from the battery.In its simplest application, the MAX1874 needs no external MOSFET or diodes, and accepts input voltages up to 6.5V; however, DC input overvoltage protection up to 18V can be added with a single SOT PFET.On-chip thermal limiting simplifies printed circuit board (PCB) layout and allows optimum charging rate without the thermal limits imposed by worst-case battery and input voltage. When the MAX1874 thermal limit is reached, the charger does not shut down but simply reduces charging current.Ambient or battery temperature can be monitored with an external thermistor. When the temperature is out of range, charging pauses.Other features include an active-low CHG output to indicate when battery current tapers below a predetermined level. DC power-OK (active-low DCOK), USB power-OK (active-low UOK), and power-on (PON) outputs indicate when valid power is present. These outputs drive logic or power-selection MOSFETs to disconnect the charging sources from the load and to protect the MAX1874 from overvoltage.The MAX1874 contains no logic for communication with the USB host. It must receive instructions from a local microcontroller. The MAX1874 is available in a 16-pin 5mm x 5mm thin QFN package and operates over the -40°C to +85°C temperature range.ApplicationsCell PhonesDigital CamerasPDAsWireless Appliances

The DS2762 high-precision Li+ battery monitor is a data-acquisition, information-storage, and safety-protection device tailored for cost-sensitive battery pack applications. This low-power device integrates precise temperature, voltage, and current measurement, nonvolatile (NV) data storage, and Li+ protection into the small footprint of either a TSSOP package or flip-chip package. The DS2762 is a key component in applications including remaining capacity estimation, safety monitoring, and battery-specific data storage.ApplicationsCell Phones/SmartphonesDigital CamerasPDAs

The MAX1259 battery manager provides backup-batteryswitching for CMOS RAM, microprocessors, or otherlow-power logic ICs. It automatically switches to thebackup battery when the primary power supply is interrupted.Low-loss switches guarantee an input-to-outputdifferential of only 200mV while supplying 250mA fromthe primary power supply or 15mA from the battery.Battery discharge during shipping does not occur in theMAX1259, since the backup battery can be disconnectedby strobing the RST input.A battery-fail output signal indicates when the backupbattery is below +2V, and a power-fail output signal indicateswhen the primary power supply is low. TheMAX1259 monitors the backup battery, warns ofimpending power failures, and switches the memory tothe battery when failures occur. The MAX1259 is pin-compatiblewith the DS1259, but consumes three timesless supply current. Commercial, extended, and militarytemperature range devices are available.ApplicationsBattery Backup for CMOS RAMComputersControllersUninterruptible Power Supplies

ADBMS2950 and ADBMS2952 are Battery Pack Monitors for electrical and hybrid vehicles, and other current or voltage sense applications. ADBMS2950 and ADBMS2952 measure the current flowing in and out of a battery pack by sensing the voltage drop over a shunt resistor with a very low offset.ADBMS2950 and ADBMS2952 also detect Overcurrent conditions using fast Overcurrent ADCs with digital threshold comparators and communicate their results through dedicated Overcurrent alert lines with minimum delay.ADBMS2950 and ADBMS2952 feature a total of 12 internally buffered high impedance inputs for measuring voltages from external sensors or resistor dividers, enabling measurement of pack voltages, temperatures, HV-Link voltages, chassis isolation, and the supervision of the state of contactors and fuses. Six digital outputs (GPO) supporting open-drain or push-pull can be used to control high voltage transistors to disconnect external resistor dividers. Four digital general-purpose inputs/outputs (GPIO) also allow operation as an I2C or SPI controller interface to address an external EEPROM or other serial peripherals.The built-in serial interface of ADBMS2950 can be configured for SPI or isolated isoSPI communication to the host. An additional isoSPI port allows to connect a daisy chain of ADBMS2950 devices; optionally extended with ADBMS6830 or ADBMS6832 (ADBMS683x) Cell Monitors. The ADBMS2952 supports SPI communication only.APPLICATIONS Electric and Hybrid Electric Vehicles Backup Battery Systems Grid Energy Storage

Switching Power Supplies 25W 5V 5A

POWER SUPPLY, PROGRAMMABLE, 3 OUTPUT; Power Supply Output Type:Programmable; No. of Outputs:3 Output; Output Voltage Min:0V; Output Voltage Max:30V; Output Current Min:0A; Output Current Max:6A; Power Rating:375W; Plug Type:-

POWER XFMR 28.0Vct@1.3A UL/cUL 115/230V SPLIT PACK PCB MOUNT/FS28-1300 RoHS Compliant: Yes

VERTICAL, 36" W/ SURGE, SWITCH ROHS COMPLIANT: YES

POWER SUPPLY MANAGEMENT CIRCUIT, ADJUSTABLE, 1 CHANNEL, PDSO14

Switching Power Supplies 1600W 380V out, Pos 4.6x2.4x.5H Non-Thrd