POWER MANAGEMENT - DC / DC;

Shunt, Buried Zener Voltage Reference IC Fixed 6.9V V ±0.29% 15 mA TO-92-3

Linear Voltage Regulator IC Positive Fixed 1 Output 150mA 8-MSOP

10 Volt Precision Reference Series Features:Very High Accuracy: 10,000 Volts 2.5mV (L and U)Low Temperature Coefficient: 3ppm/CPerformance Guaranteed -55C to +125C10mA Output Current CapabilityLow NoiseShort Circuit ProtectedAvailable as /883B

High Precision, Impedance & Electrochemical Front End Features: Analog input 16-bit ADC with both 800 kSPS and 1.6 MSPS options Voltage, current, and impedance measurement capability Internal and external current and voltage channels Ultralow leakage switch matrix and input mux Input buffers and programmable gain amplifier Voltage DACs Dual output voltage DAC with an output range of 0.2 V to 2.4 V 12-bit VBIAS0 output to bias potentiostat 6-bit VZERO0 output to bias TIA Ultra low power: 1 µA 1 high speed, 12-bit DAC Output range to sensor: ±607 mV Programmable gain amplifier on output with gain settings of 2 and 0.05 Amplifiers, accelerators, and references 1 low power, low noise potentiostat amplifier suitable for potentiostat bias in electrochemical sensing 1 low noise, low power TIA, suitable for measuring sensor current output 50 pA to 3 mA range Programmable load and gain resistors for sensor output Analog hardware accelerators Digital waveform generator Receive filters Complex impedance measurement (DFT) engine 1 high speed TIA to handle wide bandwidth input signals from 0.015 Hz up to 200 kHz Digital waveform generator for generation of sinusoid and trapezoid waveforms 2.5 V and 1.82 V internal reference voltage sources System level power savings Fast power-up and power-down analog blocks for duty cycling Programmable AFE sequencer to minimize workload of host controller 6 kB SRAM to preprogram AFE sequences Ultra low power potentiostat channel: 6.5 µAof current consumption when powered on and all other blocks in hibernate mode Smart sensor synchronization and data collection Cycle accurate control of sensor measurement Sequencer controlled GPIOs On-chip peripherals SPI serial input/output Wake-up timer Interrupt controller Power 2.8 V to 3.6 V supply 1.82 V input/output compliant Power-on reset Hibernate mode with low power DAC and potentiostat amplifier powered up to maintain sensor bias Package and temperature range 3.6 mm × 4.2 mm, 56-ball WLCSP 7 mm × 7 mm, 48-lead LFCSP Fully specified for operating temperature range of −40°C to +85°C AD5940 and AD5941 fully specified for operating temperature range of −40°C to +85°C AD5941W fully specified for operating temperature range of −40°C to +105°C AEC-Q100 qualified for automotive applications

Low Cost, Low Power, True RMS-to-DC Converter Features: Converts an ac voltage waveform to a dc voltage and then converts to the true rms, average rectified, or absolute value 200 mV rms full-scale input range (larger inputs with input attenuator) High input impedance: 1012 Ω  Low input bias current: 25 pA maximum High accuracy: ±0.3 mV ± 0.3% of reading RMS conversion with signal crest factors up to 5 Wide power supply range: +2.8 V, −3.2 V to ±16.5 V Low power: 200 μA maximum supply current Buffered voltage output No external trims needed for specified accuracy Related device: the AD737 features a power-down control with standby current of only 25 μA; the dc output voltage is negative and the output impedance is 8 kΩ

25A, Dual PolyPhase Regulator with Digital Power System Management Features: PMBus/I2C Compliant Serial Interface Telemetry Read-Back Includes VIN, IIN, VOUT, IOUT, Temperature and Faults Programmable Voltage, Current Limit, Digital Soft-Start/Stop, Sequencing, Margining, OV/UV/OC Sub-Milliohm DCR Current Sensing Digitally Adjustable Loop Compensation Parameters 0.5% Output Voltage Accuracy Over Temperature Integrated Input Current Sense Amplifier Internal EEPROM with ECC and Fault Logging Integrated N-Channel MOSFET Gate Drivers

Anyside High Voltage Isolated Switch Controller with I2C Command and Telemetry Features: CSA (IEC/UL) Approved, File #255632 Reinforced Insulation Integrated Isolated Power Supply Adjustable Turn-On Ramp Rate and Current Limit I2C/SMBus Interface 10-Bit ADC Monitors Current and Two Uncommitted Channels High Common Mode Transient Immunity: ≥ 30kV/μs Fault Status Alert and Power Good Outputs Independent 3V to 5.5V Logic Supply ±20kV ESD Across the Isolation Barrier Maximum Continuous Working Voltage: 690VRMS 14.6mm Creepage Distance Low Current Shutdown Mode (<10μA) 22mm × 9mm × 5.16mm BGA Package

25V, 600mA Buck-Boost DC/DC Converter with 1.6A Quiescent Current Features: Regulates VOUT Above, Below or Equal to VIN Wide VIN Range: 2.4V to 25V, <1V to 25V (Using EXTVCC Input) VOUT Range: 1V to 25V Adjustable Output Voltage (LTC3130) Four Selectable Fixed Output Voltages (LTC3130-1) 1.2µA No-Load Input Current in Burst Mode® Operation (VIN = 12V, VOUT = 5V) 600mA Output Current in Buck Mode Pin-Selectable 850mA/450mA Current Limit (LTC3130) Up to 95% Efficiency Pin-Selectable Burst Mode Operation 1.2MHz Ultralow Noise PWM Frequency Accurate RUN Pin Threshold n Power Good Indicator Programmable Maximum Power Point Control IQ = 500nA in Shutdown Thermally-Enhanced 20-Lead 3mm × 4mm QFN and 16-Lead MSOP Packages

40A DC/DC Module Regulator Features: Stacked Inductor Acts as Heat Sink Wide Input Voltage Range: 4.7V to 15V 0.6V to 3.3V Output Voltage Range ±1.3% Total DC Output Voltage Error Over Line, Load and Temperature (–40°C to 125°C) Differential Remote Sense Amplifier for Precision Regulation Current Mode Control/Fast Transient Response Frequency Synchronization Parallel Current Sharing (Up to 240A) Internal or External Compensation 88% Efficiency (12VIN, 1VOUT) at 40A Overcurrent Foldback Protection 16mm × 16mm × 7.07mm BGA Package