Attenuators Fixed atten 4 dB

The AD8349 is high performance quadrature modulator design for use as a single stage up-converter within wireless infrastructure equipment.The AD8349 provides a high output power and very low noise floor supporting a significant improvement in the output signal range. Additionally the excellent phase and amplitude balance accuracy support a higher sideband suppression specification enabling higher order / capacity QAM modulated radios.The AD8349 has been tested for use over the common Cellular bands (900 MHz, 1.9 GHz, 2.1 GHz) meeting the needs as specified by the CDMA/GSM Edge/W-CDMA standards.The AD8349 is supplied in 16-lead Thin Shrunk Small Outline (TSSOP) package, and fully specified over -40ºC to 85ºC temperature range.APPLICATIONS Cellular/PCS communication systems infrastructure WCDMA/CDMA2000/PCS/GSM/EDGE Wireless LAN/wireless local loop LMDS/broadband wireless access systemsAVAILABILITYSamples (part number AD8349ARE) and an evaluation board (part number AD8349-EVAL) are available. Other Modulator / Demodulator ProductsAD8345 - 250 - 1000 MHz RF / IF Quadrature ModulatorAD8346 - 2.5 GHz Direct Conversion Quadrature ModulatorAD8347 - 800 MHz to 2.7 GHz RF / IF Quadrature DemodulatorAD8348 - 50 - 1000 MHz RF / IF Quadrature Demodulator

The AD8351 is a low cost differential amplifier useful in RF andIF applications up to 2.2 GHz. The voltage gain can be set fromunity to 26 dB using a single external gain resistor. The AD8351provides a nominal 150 Ω differential output impedance. Theexcellent distortion performance and low noise characteristicsof this device allow for a wide range of applications.The AD8351 is designed to satisfy the demanding performancerequirements of communications transceiver applications. Thedevice can be used as a general-purpose gain block, an ADCdriver, and a high speed data interface driver, among otherfunctions. The AD8351 can also be used as a single-ended-to-differentialamplifier with similar distortion products as in thedifferential configuration. The exceptionally good distortionperformance makes the AD8351 an ideal solution for 12-bit and14-bit IF sampling receiver designs.Fabricated in Analog Devices, Inc., high speed XFCB process,the AD8351 has high bandwidth that provides high frequencyperformance and low distortion. The quiescent current of theAD8351 is 28 mA typically. The AD8351 amplifier comes in acompact 10-lead MSOP package or in a 16-lead LFCSP package,and operates over the temperature range of −40°C to +85°C.Applications Differential ADC drivers Single-ended-to-differential conversion IF sampling receivers RF/IF gain blocks SAW filter interfacing AvailabilityOther RF / IF amplifiers products:AD8367 - 500 MHz Single Ended, Analog Controlled VGA AD8369 - 600 MHz, 45 dB Digitally Controlled Variable Gain Amplifier AD8350 - 1.0 GHz Differential Amplifier

The HMC273AMS10G(E) is a general purposebroadband 5-Bit positive control GaAs IC digitalattenuator in a 10 lead MSOP plastic package.Covering 0.7 to 3.8 GHz, the insertion loss is typicallyless than 3 dB. The attenuator bit values are1 (LSB), 2, 4, 8, and 16 dB for a total attenuationof 31 dB. Accuracy is excellent at ±0.2 dB typicalwith an IIP3 of up to +46 dBm. Five bit control voltageinputs, toggled between 0 and +3 to +5 volts, areused to select each attenuation state. A single Vddbias of +3 to +5 volts applied through an external5K Ohm resistor is required.Applications Cellular; UMTS/3G infrastructure ISM, MMDS, WLAN, WiMAX Microwave radio & VSAT Test equipment and sensors

The HMC1049 is a GaAs MMIC low noise amplifier (LNA) that operates between 0.3 GHz and 20 GHz. This LNA provides 16 dB of small signal gain, a 1.7 dB noise figure, and an Output IP3 of 27 dBm, requiring only 70 mA from a 7 V supply. The P1dB output power of 16 dBm enables the LNA to function as a local oscillator (LO) driver for balanced, I/Q or image rejection mixers. VDD can be applied to Pad 2 with VDD = 7 V or to Pad 4 with VDD = 4 V. Pad 4 requires a bias tee. The HMC1049 is also internally matched to 50 Ω for ease of integration into multichip modules (MCMs). All data is taken with the chip in a 50 Ω test fixture connected via 0.025 mm (1 mil) diameter wire bonds of 0.31 mm (12 mil) length.Applications Point-to-point radios Point-to-multipoint radios Military and space Test instrumentation

The HMC1097LP4E is a low noise, high linearity Direct Quadrature Modulator RFIC which is ideal for digital modulation applications from 0.1 to 6.0 GHz including; Cellular/3G, WiMAX/4G, Broadband Wireless Access & ISM circuits. Housed in a compact 4x4 mm (LP4) SMT QFN package, the RFIC requires minimal external components & provides a low cost alternative to more complicated double upconversion architectures. The RF output port is single-ended and matched to 50 Ohms with no external components. The LO requires -6 to +6 dBm and can be driven in either differential or single-ended mode. This device is optimized for a +5V supply, and offers improved carrier feedthrough and sideband suppression characteristics.APPLICATIONS UMTS, GSM or CDMA Basestations Fixed Wireless or WLL ISM Transceivers, 900 & 2400 MHz GMSK, QPSK, QAM, SSB Modulators Cellular/3G and WiMAX/4G

The HMC316MS8(E) is a miniature double balanced mixer in 8 lead plastic surface mount package. The passive GaAs schottky diode mixer implements planar on chip balun transformers, and requires no external components. The mixer can be used as an upconverter, downconverter, or modulator. At mid-band the mixer provides 7.5 dB conversion loss and +25 dBm IIP3 with LO drive levels of +19 dBm. The design was optimized for low cost high volume applications where high converter linearity is required.Applications Cellular Basestations Cable Modems Fixed Wireless Access Systems WiMAX

The HMC400MS8(E) is a high dynamic range passive MMIC mixer in plastic surface mount 8 lead Mini Small Outline Package (MSOP) covering 1.7 to 2.2 GHz. Excellent input IP3 performance of +36 dBm for down conversion and +29 dBm for up conversion is provided for 2.5G & 3G GSM/CDMA based UMTS or PCS applications at an LO drive of +17dBm. With a 1dB compression of +21 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 8.5dB typical and LO isolations are maintained at 22 to 33 dB.This miniature single-ended monolithic GaAs FET mixer does not require any external components or bias. The 50 to 300 MHz IF frequency response will satisfy many UMTS/PCS transmit or receive frequency plans configured for low side LO. The HMC400MS8(E) input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm² standard IC footprint and no DC bias.Applications GSM, GPRS & EDGE CDMA & W-CDMA Cable Modem Termination Systems

The HMC407MS8G & HMC407MS8GE are high efficiency GaAs InGaP Heterojunction Bipolar Transistor (HBT) MMIC Power amplifiers which operate between 5 and 7 GHz. The amplifier requires no external matching to achieve operation and is thus truly 50 Ohm matched at input and output. The amplifier is packaged in a low cost, surface mount 8 leaded package with an exposed base for improved RF and thermal performance. The amplifier provides 15 dB of gain, +29 dBm of saturated power at 28% PAE from a +5V supply voltage. Power down capability is available to conserve current consumption when the amplifier is not in use.Applications UNII HiperLAN

The HMC465LP5(E) is a GaAs MMIC PHEMT DistributedDriver Amplifier packaged in leadless 5x5mm surface mount package which operate betweenDC and 20 GHz. The amplifier provides 15 dB of gain,3 dB noise figure and +25 dBm of saturated outputpower while requiring only 160 mA from a +8V supply.Gain flatness is excellent at ±0.5 dB as well as ±4deg deviation from linear phase from DC - 10 GHzmaking the HMC465LP5(E) ideal for OC192 fiberoptic LN/MZ modulator driver amplifiers as well astest equipment applications. The HMC465LP5(E)amplifiers I/Os are internally matched to 50 Ohms.Applications OC192 LN/MZ modulator driver Microwave radio andVSAT Test instrumentation Military EW, ECM & C³I