Micropower 3-Sensor Combination Including Acceleration and Temperature Features: All sensors sampled synchronously Up to 400 Hz ODR Samples can be synchronized to external trigger Ultralow power 1.95 A at 100 Hz ODR, 2.0 V supply, all sensors on 270 nA at 6 Hz motion activated wake-up mode 10 nA standby current 12-bit resolution for all sensors Acceleration scale factor down to 1 mg/LSB Temperature scale factor: 0.065C/LSB (typical) Built-in features for motion-based system level power savings Adjustable threshold sleep/wake modes for motion activation Accelerometer, temperature sensor, and provision for third analog sensor input Autonomous interrupt processing, without need for microcontroller intervention, to allow the rest of the system to be turned off completely Deep embedded FIFO minimizes host processor load Awake state output enables implementation of standalone, motion activated switch Wide supply and I/O voltage ranges: 1.6 V to 3.5 VOperates off 1.8 V to 3.3 V railsPower can be derived from coin cell batterySPI digital interfaceSmall and thin 3 mm 3.25 mm 1.06 mm package

Micropower, 3-Axis, 200 g Digital Output, MEMS Accelerometer Features: ±200 g measurement range 160 Hz to 2560 Hz user selectable bandwidth with four-pole antialiasing filter Selectable oversampling ratio Adjustable high-pass filter Ultra low power Power can be derived from a coin cell battery 28 µA at 2560 Hz ODR, 3.3 V supply Low power, wake-up mode for low g activity detection 1.7 A instant on mode with adjustable threshold Built in features for system level power savings Autonomous interrupt processing without processor intervention Ultra low power event monitoring detects impacts and wakes up fast enough to capture the transient events Adjustable, low g threshold activity and inactivity detection Wide operating voltage range: 2.5 V to 3.5 V Acceleration sample synchronization via external trigger SPI digital interface and I2C interface format support 12-bit output at 100 mg/LSB scale factor Wide temperature range: 40°C to +105°C Small, thin, 3 mm × 3.25 mm × 1.06 mm package

Ultralow noise, dual-axis MEMS Gyroscope for Stabilization Applications Features: Pitch and roll rate gyroscope Ultralow noise: 0.004°/s/√Hz High vibration rejection over a wide frequency range Power saving standby mode 80 µA current consumption in standby mode Fast startup time from standby mode: <100 ms Low delay of <0.5 ms for a 30 Hz input at the widest bandwidth setting Serial peripheral interface (SPI) digital output Programmable high-pass and low-pass filters 2000 g powered acceleration survivability 2.7 V to 5.0 V operation −25°C to +85°C operation 4.5 mm × 5.8 mm × 1.2 mm cavity laminate package

Low Noise, Wide Bandwidth, MEMS Accelerometer Features: Single, in-plane axis accelerometer with analog output Full-scale range: ±200 g Linear frequency response range: dc to 15 kHz typical (3 dB point) Resonant frequency: 28 kHz typical Sensitivity performance Sensitivity stability over temperature within ± 5% Linearity to ±0.2% of full-scale range Cross-axis sensitivity ± 1%/± 0.8% (z-axis acceleration effect on x-axis, y-axis acceleration effect on x-axis) Ultralow noise density 45 μg/√Hz Overrange sensing plus dc coupling allows fast recovery time Complete electromechanical self test Single-supply operation Output voltage ratiometric to supply Low power consumption: 1.0 mA typical Power saving standby operation mode with fast recovery RoHS compliant −40°C to +125°C temperature range 32-lead, 5 mm × 5 mm × 1.8 mm LFCSP package

Small, Low Power, 3-Axis 2 g Accelerometer Features:3-axis sensingSmall, low profile package4 mm 4 mm 1.45 mm LFCSPLow power: 350 A typicalSingle-supply operation: 1.8 V to 3.6 V10,000 g shock survivalExcellent temperature stabilityBandwidth adjustment with a single capacitor per axisRoHS/WEEE lead-free compliant

Nanopower, 3-Axis, 2 g/4 g/8 g Digital Output MEMS Accelerometer Features: Supply voltage range Single-cell battery operation: 1.1 V to 3.6 V Internal power supply regulation for high PSRR Ultralow power 0.89 μA at 100 Hz ODR, 2.0 V supply 180 nA motion activated wake-up mode 40 nA standby current High resolution: 0.25 mg/LSB Built-in features for system level power savings Single-tap and double-tap detection with only 35 nA of added current Adjustable threshold sleep and wake-up modes for motion activation Autonomous interrupt processing, without need for microcontroller intervention, to allow the rest of the system to be turned off completely Deep 512 sample embedded FIFO minimizes host processor load Awake state output enables implementation of motion activated switch Low noise to 170 μg/√Hz Acceleration sample synchronization via external trigger On-chip temperature sensor Internal two-pole antialias filter SPI (4-wire) and I2C digital interfaces Small and thin 2.2 mm × 2.3 mm × 0.87 mm package

Micropower, 3-Axis, 400 g, Digital Output, MEMS Accelerometer Features: ±400 g measurement range 160 Hz to 2560 Hz user selectable bandwidth with 4-pole antialiasing filter Selectable oversampling ratio Adjustable high-pass filter Ultra Low power Power can be derived from a coin cell battery 19 μA at 2560 Hz ODR, 2.5 V supply Low power wake-up mode for low g activity detection 1.4 μA instant on mode with adjustable threshold 0.1 μA standby mode Built-in features for system level power savings Autonomous interrupt processing without processor intervention Ultra low power event monitoring: detects impacts and wakes up fast enough to capture the transient events Adjustable low g threshold activity and inactivity detection Wide operating voltage range: 1.6 V to 3.5 V Acceleration sample synchronization via external trigger SPI digital interface and I2C interface format support 12-bit output at 200 mg/LSB scale factor Wide temperature range: −40°C to +105°C Small, thin 3.00 mm × 3.25 mm × 1.06 mm package

The ADXL203 is a high precision, low power, complete dual-axis accelerometer with signal conditioned voltage outputs, all on a single, monolithic IC. The ADXL203 measures acceleration with a full-scale range of ?1.7 g, ?5 g, or ?18 g. The ADXL203 can measure both dynamic acceleration (for example, vibration) and static acceleration (for example, gravity).The typical noise floor is 110 ?g/?Hz, allowing signals below 1 mg (0.06? of inclination) to be resolved in tilt sensing applications using narrow bandwidths (<60 Hz). The user selects the bandwidth of the accelerometer using Capacitor CX and Capacitor CY at the XOUT and YOUT pins. Bandwidths of 0.5 Hz to 2.5 kHz can be selected to suit the application.The ADXL203 is available in a 5 mm ? 5 mm ? 2 mm, 8-terminal ceramic LCC package.Applications: Platform stabilization/leveling Navigation Alarms and motion detectors High accuracy, 2-axis tilt sensing Vibration monitoring and compensation Abuse event detection

The ADXL204 is a high precision, low power, complete dual-axis accelerometer with signal-conditioned voltage outputs, all on a single monolithic IC. Like the ADXL203, it measures acceleration with a full-scale range of ?1.7 g; however, the ADXL204 is tested and specified for 3.3 V supply voltage, whereas the ADXL203 is tested and specified at 5 V. Both parts function well over a wide 3 V to 6 V operating voltage range. The ADXL204 can measure both dynamic acceleration (for example, vibration) and static acceleration (for example, gravity).The typical noise floor is 170 ?g/?Hz, allowing signals below 2 mg (0.1? of inclination) to be resolved in tilt sensing applications using narrow bandwidths (<60 Hz).The user selects the bandwidth of the accelerometer using Capacitor CX and Capacitor CY at the XOUT and YOUT pins. Bandwidths of 0.5 Hz to 2.5 kHz can be selected to suit the application.The ADXL204 is available in a 5 mm ? 5 mm ? 2 mm, 8-terminal hermetic LCC package.APPLICATIONS Vehicle dynamic control (VDC)/electronic stability program (ESP) systems Electronic chassis controls Electronic braking Platform stabilization/leveling Navigation Alarms and motion detectors High accuracy, 2-axis tilt sensing

The ADIS16475 is a precision, miniature MEMS inertial measurement unit (IMU) that includes a triaxial gyroscope and a triaxial accelerometer. Each inertial sensor in the ADIS16475 combines with signal conditioning that optimizes dynamic performance. The factory calibration characterizes each sensor for sensitivity, bias, alignment, linear acceleration (gyroscope bias), and point of percussion (accelerometer location). As a result, each sensor has dynamic compensation formulas that provide accurate sensor measurements over a broad set of conditions.The ADIS16475 provides a simple, cost effective method for integrating accurate, multiaxis inertial sensing into industrial systems, especially when compared with the complexity and investment associated with discrete designs. All necessary motion testing and calibration are part of the production process at the factory, greatly reducing system integration time. Tight orthogonal alignment simplifies inertial frame alignment in navigation systems. The serial peripheral interface (SPI) and register structure provide a simple interface for data collection andconfiguration control.The ADIS16475 is available in a 44-ball, ball grid array (BGA) package that is approximately 11 mm ? 15 mm ? 11 mm.Applications Navigation, stabilization, and instrumentation Unmanned and autonomous vehicles Smart agriculture and construction machinery Factory/industrial automation, robotics Virtual/augmented reality Internet of Moving Things