600 mA, Ultralow Noise, High PSRR, RF Linear Regulator Features: Input voltage range: 2.3 V to 5.5 V Maximum load current: 600 mA Low noise 0.9 µV rms total integrated noise from 100 Hz to 100 kHz 1.6 µV rms total integrated noise from 10 Hz to 100 kHz Noise spectral density: 1.5 nV/√Hz from 10 kHz to 1 MHz PSRR of 90 dB from 200 Hz to 200 kHz; 58 dB at 1 MHz, VOUT = 3.3 V, VIN = 3.8 V Dropout voltage: 120 mV typical at VOUT = 3.3 V, IOUT = 600 mA Initial accuracy: ±0.5% Accuracy over line, load, and temperature: −2.0%(minimum), +1.5% (maximum), from −40°C to +85°C Quiescent current, IGND = 4 mA at no load Low shutdown current: 0.2 μA Stable with a 10 µF ceramic output capacitor Adjustable and fixed output voltage options: 1.2 V, 1.8 V, 2.5 V, 2.8 V, 3.0 V, 3.3 V (16 standard voltages between 1.2 V and 3.3 V available) 8-lead LFCSP and 8-lead SOIC packages Precision enable Supported by ADIsimPower tool

Ultralow Noise, 200 mA, Linear Regulator Features: PSRR performance of 54 dB at 100 kHz Ultralow noise independent of VOUT 3 μV rms, 0.1 Hz to 10 Hz 9.5 μV rms, 0.1 Hz to 100 kHz 9 µV rms, 10Hz to 100KHz 17 µV rms, 10Hz to 1MHz Low dropout voltage: 150 mV at 200 mA load Maximum output current: 200 mA Input voltage range: 2.2 V to 5.5 V Low quiescent and shutdown current Initial accuracy: ±1% Accuracy over line, load, and temperature: −2.5%/+1.5% 5-lead TSOT package and 6-lead LFCSP package

Microprocessor Supervisory Circuit with Watchdog Feature, 4.65V Threshold Voltage, Low Supply Current and Active Low Reset Output. Upgrade for ADM699 Features: Superior Upgrade for ADM698/ADM699, MAX698/MAX699 Guaranteed RESET Assertion with VCC = 1 V Low 70 µA Supply Current Precision 4.65 V Voltage Monitor Power OK/Reset Time Delay Power OK/Reset Time Delay Watchdog Timer Minimum Component Count Performance Specified over Temperature ADM8698 is obsolete

3 V, LVDS, Quad CMOS Differential Line Receiver Features: ±8 kV ESD IEC 61000-4-2 contact discharge on receiver input pins 400 Mbps (200 MHz) switching rates 100 ps channel-to-channel skew (typical) 3.3 ns propagation delay (maximum) 3.3 V power supply High impedance outputs on power-down Please see data sheet for additional features.

Triple-Channel, Digital Isolator, Enhanced System-Level ESD Reliability (2/1 channel directionality) Features: Enhanced system-level ESD performance per IEC 61000-4-x Low power operation 5 V operation 2.0 mA per channel maximum at 0 Mbps to 2 Mbps 4.1 mA per channel maximum at 10 Mbps 36 mA per channel maximum at 90 Mbps 3.3 V operation 1.0 mA per channel maximum at 0 Mbps to 2 Mbps 2.8 mA per channel maximum at 10 Mbps 17 mA per channel maximum at 90 Mbps Bidirectional communication 3.3 V/5 V level translation High temperature operation: 105°C High data rate: dc to 90 Mbps (NRZ) Precise timing characteristics 2 ns maximum pulse width distortion 2 ns maximum channel-to-channel matching High common-mode transient immunity: >25 kV/μs Output enable function 16-lead SOIC wide body, RoHS-compliant package Safety and regulatory approvals UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice 5A VDE Certificate of Conformity DIN V VDE V 0884-10 (VDE V 0884-10): 2006-12 VIORM = 560 V peak CQC Certification per GB4943.1-2011

Micropower 3-Sensor Combination Including Acceleration and Temperature Features: All sensors sampled synchronously Up to 400 Hz ODR Samples can be synchronized to external trigger Ultralow power 1.95 A at 100 Hz ODR, 2.0 V supply, all sensors on 270 nA at 6 Hz motion activated wake-up mode 10 nA standby current 12-bit resolution for all sensors Acceleration scale factor down to 1 mg/LSB Temperature scale factor: 0.065C/LSB (typical) Built-in features for motion-based system level power savings Adjustable threshold sleep/wake modes for motion activation Accelerometer, temperature sensor, and provision for third analog sensor input Autonomous interrupt processing, without need for microcontroller intervention, to allow the rest of the system to be turned off completely Deep embedded FIFO minimizes host processor load Awake state output enables implementation of standalone, motion activated switch Wide supply and I/O voltage ranges: 1.6 V to 3.5 VOperates off 1.8 V to 3.3 V railsPower can be derived from coin cell batterySPI digital interfaceSmall and thin 3 mm 3.25 mm 1.06 mm package

Operational Amplifiers - Op Amps VLTG-FDBK, G= 2 CLAMP AMP

3-V, RS-232 Serial Port Driver-Receiver Features: Green Idle power-saving mode Single 2.7 V to 3.6 V power supply Operates with 3 V logic 0.1 µF to 1 µF charge pump capacitors Low EMI Low power shutdown: 20 nA Full RS-232 compliance 460 kb/s data rate One receiver active in shutdown (ADM3307E/ADM3311E/ADM3312E/ADM3315E) Two receivers active in shutdown (ADM3310E) ESD >15 kV IEC 1000-4-2 on RS-232 I/Os ESD >15 kV IEC 1000-4-2 on CMOS and RS-232 I/Os (ADM3307E) Qualified for automotive applications

2 A/1.2 A DC-to-DC Switching Regulator with Independent Positive and Negative Outputs Features: Wide input supply voltage range: 2.85 V to 15 V Generates well regulated, independently resistor programmable VPOS and VNEG outputs Boost regulator to generate VPOS output Adjustable positive output to 39 V Integrated 2.0 A main switch Optional single-ended primary-inductor converter (SEPIC) configuration for automatic step-up/step-down Inverting regulator to generate VNEG output Adjustable negative output to VIN − 39 V Integrated 1.2 A main switch True shutdown for both positive and negative outputs 1.2 MHz/2.4 MHz switching frequency with optional external frequency synchronization from 1.0 MHz to 2.6 MHz Resistor programmable soft start timer Slew rate control for lower system noise Individual precision enable and flexible start-up sequence control for symmetric start, VPOS first, or VNEG first Out-of-phase operation UVLO, OCP, OVP, and TSD protection 4 mm × 4 mm, 20-lead LFCSP and 20-lead TSSOP −40°C to +125°C junction temperature range Supported by the ADIsimPower tool set

Integrated Optical Module for Smoke Detection Features: Supports UL-217 edition 8/ UL-568 ed. 7; EN-54; GB..; ISO Lowers Nuisance Alarms using a Dual Wavelength detection with higher SNR and dynamic range. 3X Lower power dissipation enables smaller/ cheaper batteries Integrated Optical Module (3.8mm x 5mm x 0.9mm with 1 blue LED, 1 IR LED and 2 Photo diodes) simplifies EMC design, allows for greater diversity of industrial design options and results in 75% fewer discrete components. Loop calibration at final test reduces calibration challenges with smoke detector products. Supported by ADI designed smoke chamber manufactured by Accumold, 28800X. (Please see EVAL-CHAMBER Mechanical Dimensions (PDF), also under Resources below)