Programmable Transimpedance, Current to Bits Receiver Module Features: High performance, current input, data acquisition μModule that includes a TIA, analog filter, ADC driver, and ADC 3 selectable TZ settings: 2 k, 20 k, and 200 k Internal 1.8 V LDO for the ADC All passive components including supply decoupling Small form factor: 12.00 mm × 6.00 mm CSP_BGA Operation from a single 3.3 V supply Full-scale input current to 800 μA (TZ = 2 k) Fast input overload recovery High analog input current to 40 mAAnalog filter for noise reduction and antialias filtering Selectable 1.0 MHz and 100 MHz LPF bandwidth Low input referred current noise: 16 pA rms TZ = 200 k, 65,536 averages, 1 MHz analog filter Supports input pulse widths down to 10 ns 14-bit ADC with sample rate up to 125 MSPS Serial LVDS data output SPI control interface Quiescent power: 546 mW, LDO enabled Temperature range: 40C to +85C

Three ADCs, One DAC, Low Power Codec with Audio/FastDSP Features: Programmable FastDSP audio processing engine Up to 768 kHz sample rate Biquad filters, limiters, volume controls, mixing Low latency, 24-bit ADCs and DAC 106 dB SNR (signal through ADC with A-weighted filter) 110 dB combined SNR (signal through DAC and headphone with A-weighted filter) Serial port sample rates from 8 kHz to 768 kHz 5 μs analog-to-analog group delay Programmable, double precision MAC engine for 13-stage equalizer 3 analog inputs (2 differential and 1 single-ended), configurable as microphone or line inputs Analog differential audio output, configurable as either line output or headphone driver PLL supporting any input clock rate from 30 kHz to 27 MHz 1-channel ASRCI, 3-channel ASRCO Serial audio ports supporting I2S, left justified, or up to 16-channel TDM (TDM16) 2 interpolators and 4 decimators with flexible routing Power supplies Analog AVDD at 1.8 V Digital I/O IOVDD at 1.8 V to 3.3 V Headphone HPVDD at 1.8 V Headphone HPVDD_L at 1.2 V to1.8 V Control/communication interfaces I2C, SPI, or UART 28-ball, 0.4 mm pitch, 2.957 mm × 1.757 mm WLCSP

Ultrafast 3.3 V Single-Supply Comparator w/CML Output Drivers Features: 3.3 V/5.2 V single-supply operation 150 ps propagation delay 15 ps overdrive and slew rate dispersion 8 GHz equivalent input rise time bandwidth 80 ps minimum pulse width 35 ps typical output rise/fall 10 ps deterministic jitter (DJ) 200 fs random jitter (RJ) On-chip terminations at both input pins Robust inputs with no output phase reversal Resistor-programmable hysteresis Differential latch control Extended industrial −40°C to +125°C temperature range

16-Bit, 50Msps DAC Features: 50Msps Update Rate Pin Compatible 12-Bit, 14-Bit and 16-Bit Devices High Spectral Purity: 87dB SFDR at 1MHz fOUT 5pV-s Glitch Impulse Differential Current Outputs 20ns Settling Time Low Power: 180mW from ±5V Supplies TTL/CMOS (3.3V or 5V) Inputs Small Package: 28-Pin SSOP

40VIN, 1.2A Silent Switcher Module Regulator Features: Low Noise Silent Switcher® Architecture CISPR 22 Class B Compliance Wide Input Voltage Range: 3.2V to 40V Wide Output Voltage Range: 0.8V to 12V 1.2A Continuous Output Current at 24VIN, 5VOUT, TA = 85°C 1.75A Peak Output Current at 3.3VOUT Selectable Switching Frequency: 200kHz to 2.2MHz External Synchronization Configurable as an Inverter 4mm × 4mm × 1.82mm BGA Package

Dual 3 MHz, 1200mA Buck Regulator with Two 300 mA LDOs Features: Main input voltage range: 2.3 V to 5.5 V Two 1200 mA buck regulators and two 300 mA LDOs 24-lead, 4 mm × 4 mm LFCSP or 28-lead TSSOP package Regulator accuracy: ±1.8% Factory programmable or external adjustable VOUTx 3 MHz buck operation with forced PWM and auto PWM/PSM modes BUCK1/BUCK2: output voltage range from 0.8 V to 3.8 V LDO1/LDO2: output voltage range from 0.8 V to 5.2 V LDO1/LDO2: input supply voltage from 1.7 V to 5.5 V LDO1/LDO2: high PSRR and low output noise

2 A/1.2 A DC-to-DC Switching Regulator with Independent Positive and Negative Outputs Features: Wide input supply voltage range: 2.85 V to 15 V Generates well regulated, independently resistor programmable VPOS and VNEG outputs Boost regulator to generate VPOS output Adjustable positive output to 39 V Integrated 2.0 A main switch Optional single-ended primary-inductor converter (SEPIC) configuration for automatic step-up/step-down Inverting regulator to generate VNEG output Adjustable negative output to VIN − 39 V Integrated 1.2 A main switch True shutdown for both positive and negative outputs 1.2 MHz/2.4 MHz switching frequency with optional external frequency synchronization from 1.0 MHz to 2.6 MHz Resistor programmable soft start timer Slew rate control for lower system noise Individual precision enable and flexible start-up sequence control for symmetric start, VPOS first, or VNEG first Out-of-phase operation UVLO, OCP, OVP, and TSD protection 4 mm × 4 mm, 20-lead LFCSP and 20-lead TSSOP −40°C to +125°C junction temperature range Supported by the ADIsimPower tool set

40 V, 200 mA, Low Noise, CMOS LDO Linear Regulator Features: Low noise: 11 μV rms independent of fixed output voltage PSRR of 88 dB at 10 kHz, 68 dB at 100 kHz, 50 dB at 1 MHz, VOUT ≤ 5 V, VIN = 7 V Input voltage range: 2.7 V to 40 V Maximum output current: 200 mA Initial accuracy: ±0.8% Accuracy over line, load, and temperature −1.2% to +1.5%, TJ = −40°C to +85°C ±1.8%, TJ = −40°C to +125°C Low dropout voltage: 200 mV (typical) at a 200 mA load, VOUT = 5 V User programmable soft start (LFCSP and SOIC only) Low quiescent current, IGND = 50 μA (typical) with no load Low shutdown current: 1.8 μA at VIN = 6 V, 3.0 μA at VIN = 40 V Stable with a small 2.2 μF ceramic output capacitor Fixed output voltage options: 1.8 V, 2.5 V, 3.3 V, 3.8 V, and 5.0 V 15 standard voltages between 1.2 V and 5.0 V are available Adjustable output from 1.2 V to VIN – VDO, output can be adjusted above initial set point Precision enable 2 mm × 2 mm, 6-lead LFCSP, 8-Lead SOIC, 5-Lead TSOT AEC-Q100 qualified for automotive applications

SPI, 1.5 RON, 15 V/5 V/+12 V, High Density Octal SPST Switch Features: SPI with error detection Includes CRC, invalid read and write address, and SCLK count error detection Supports burst mode and daisy-chain mode Industry-standard SPI Mode 0 and Mode 3 interface compatible Integrated passive components Route through of digital signals and supplies Guaranteed break-before-make switching allowing external wiring of switches to deliver multiplexer configurations 1.5 typical on resistance at 25°C (±15 V dual supply) 0.3 typical on resistance flatness at 25°C (±15 V dual supply) 0.1 typical on resistance match between channels at 25°C (±15 V dual supply) VSS to VDD analog signal range Fully specified at ±15 V, ±5 V, and +12 V 1.8 V logic compatibility with 2.7 V ≤ VL ≤ 3.3 V (excludes SPI readback to a 1.8 V device) 4 mm × 5 mm, 30-terminal LGA 

Precision, Miniature MEMS IMU

Features:

• Triaxial, digital gyroscop
  • ±125°/sec, ±500°/sec, ±2000°/sec dynamic range models
  • 2.3°/hr in-run bias stability (ADIS16507-1)
  • 0.13°/√hr angular random walk, x-axis and y-axis, 1 σ (ADIS16507-1)
  • ±0.25° axis to axis misalignment error
• Triaxial, digital accelerometer, ±392 m/sec2 dynamic range
  • 125 μm/sec2 in-run bias stability, x-axis and y-axis, 1 σ
• Triaxial, delta angle and delta velocity outputs
• Factory calibrated sensitivity, bias, and axial alignment
  • Calibration temperature range: −40°C to +85°C
• SPI compatible data communications
• Programmable operation and control
  • Automatic and manual bias correction controls
  • Data ready indicator for synchronous data acquisition
  • External sync modes: direct, scaled, and output
  • On demand self-test of inertial sensors
  • On demand self-test of flash memory
• Single-supply operation (VDD): 3.0 V to 3.6 V
• 19,600 m/sec2 mechanical shock survivability
• Operating temperature range: −40°C to +105°C

Applications:

• Navigation, stabilization, and instrumentation
• Unmanned and autonomous vehicles
• Smart agriculture and construction machinery
• Factory/industrial automation, robotics
• Virtual/augmented reality
• Internet of Moving Things