The ADG526A and ADG527A are CMOS monolithic analog multiplexers with 16 single channels and dual 8 channels, respectively. On-chip latches facilitate microprocessor interfacing. The ADG526A switches one of 16 inputs to a common output, depending on the state of four binary addresses and an enable input. The ADG527A switches one of eight differential inputs to a common differential output, depending on the state of three binary addresses and an enable input. Both devices have TTL and 5 V CMOS logic-compatible digital inputs. The ADG526A and ADG527A are designed on an enhanced LC2MOS process that gives an increased signal capability of VSS to VDD and enables operation over a wide range of supply voltages. The devices can comfortably operate anywhere in the 10.8 V to 16.5 V single- or dual-supply range. These multiplexers also feature high switching speeds and low RON. PRODUCT HIGHLIGHTS Single- or Dual-Supply Specifications with a Wide Tolerance. The devices are specified in the 10.8 V to 16.5 V range for both single and dual supplies. Easily Interfaced. The ADG526A and ADG527A can be easily interfaced with microprocessors. The WR signal latches the state of the address control lines and the enable line. The RS signal clears both the address and enable data in the latches, resulting in no output (all switches off). RS can be tied to the microprocessor reset pin. Extended Signal Range. The enhanced LC2MOS processing results in a high breakdown and an increased analog signal range from VSS to VDD. Break-Before-Make Switching. Switches are guaranteed break-before-make so that input signals are protected against momentary shorting. Low Leakage. Leakage currents in the range of 20 pA make these multiplexers suitable for high precision circuits.APPLICATIONS Data acquisition systems Communication systems Automatic test equipment Microprocessor controlled systems

The ADG601 / ADG602 are monolithic, CMOS single-pole single-throw (SPST) switches with on resistance typically less than 2.5 Ω. The low on-resistance flatness makes the ADG601 / ADG602 ideally suited to many applications, particularly those requiring low distortion. These switches are ideal replacements for mechanical relays because they are more reliable, have lower power requirements, and are available in much smaller package sizes.The ADG601 is a normally open (NO) switch, and the ADG602 is a normally closed (NC) switch. Each switch conducts equally well in both directions when the device is on, with the input signal range extending to the supply rails.The switches are available in tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die.PRODUCT HIGHLIGHTS Low on resistance (2 Ω typical) Dual ±2.7 V to ±5.5 V or single +2.7 V to +5.5 V supplies Tiny, 6-lead SOT-23; 8-lead MSOP; and 820 μm × 2255 μm die Rail-to-rail input signal rangeAPPLICATIONS Automatic test equipment Power routing Communication systems Data acquisition systems Sample-and-hold systems Avionics Relay replacement Battery-powered systems

The ADG609 is a monolithic CMOS analog multiplexer comprising four differential channels. The ADG609 switches one of four differential inputs to a common differential output as determined by the 2-bit binary address lines A0 and A1. An EN input on both devices is used to enable or disable the device. When disabled, all channels are switched OFF.The ADG609 is designed on an enhanced LC2 MOS process which provides low power dissipation yet gives high switching speed and low on resistance. Each channel conducts equally well in both directions when ON and has an input signal range which extends to the supplies. In the OFF condition, signal levels up to the supplies are blocked. All channels exhibit break before make switching action preventing momentary shorting when switching channels. Inherent in the design is low charge injection for minimum transients when switching the digital inputs.

The ADG759 is a low voltage, CMOS analog multiplexer comprising four differential channels. The ADG759 switches one of four differential inputs to a common differential output as determined by the 2-bit binary address lines A0 and A1. An EN input is used to enable or disable the device. When disabled, all channels are switched OFF.Low power consumption and operating supply range of 1.8 V to 5.5 V make the ADG759 ideal for battery-powered, portable instruments. All channels exhibit break-before-make switching action preventing momentary shorting when switching channels.The ADG759 is available in a 16-lead TSSOP package.APPLICATIONS Data Acquisition Systems Communication Systems Relay Replacement Audio and Video Switching Battery-Powered SystemsPRODUCT HIGHLIGHTS Small 20-Lead 4 mm × 4 mm Chip Scale Packages (CSP). Single/Dual Supply Operation. The ADG758 and ADG759 are fully specified and guaranteed with 3 V and 5 V single-supply and ±2.5 V dual-supply rails. Low RON (3 Ω Typical). Low Power Consumption (<0.01 µW). Guaranteed Break-Before-Make Switching Action.

The ADG774 is a monolithic CMOS device comprising four 2:1 multiplexer/demultiplexers with high impedance outputs. The CMOS process provides low power dissipation yet gives high switching speed and low on resistance. The on-resistance variation is typically less than 0.5 Ω with an input signal ranging from 0 V to 5 V.The bandwidth of the ADG774 is greater than 200 MHz and this, coupled with low distortion (typically 0.5%), makes the part suitable for switching fast ethernet signals.The on-resistance profile is very flat over the full analog input range ensuring excellent linearity and low distortion when switching audio signals. Fast switching speed, coupled with high signal bandwidth, also makes the parts suitable for video signal switching. CMOS construction ensures ultralow power dissipation making the parts ideally suited for portable and battery powered instruments.PRODUCT HIGHLIGHTS Wide –3 dB Bandwidth, 240 MHz. Ultralow Power Dissipation. Extended Signal Range. The ADG774 is fabricated on a CMOS process giving an increased signal range that fully extends to the supply rails. Low Leakage Over Temperature. Break-Before-Make Switching. This prevents channel shorting when the switches are configured as a multiplexer. Crosstalk Typically –70 dB @ 30 MHz. Off Isolation Typically –60 dB @ 10 MHz.APPLICATIONS USB 1.1 Signal Switching Circuits Cell Phones PDAs Battery-Powered Systems Communications Systems Data Acquisition Systems Token Ring 4 Mbps/16 Mbps Audio and Video Switching Relay Replacement

The AD9785/AD9787/AD9788 are 12-bit, 14-bit, and 16-bit,high dynamic range TxDAC® devices, respectively, that providea sample rate of 800 MSPS, permitting multicarrier generationup to the Nyquist frequency. Features are included for optimizingdirect conversion transmit applications, including complexdigital modulation, as well as gain, phase, and offset compensation.The DAC outputs are optimized to interface seamlesslywith analog quadrature modulators, such as the ADL5375family from Analog Devices, Inc. A serial peripheral interface(SPI) provides for programming and readback of many internalparameters. Full-scale output current can be programmed overa range of 10 mA to 30 mA. The AD9785/AD9787/AD9788family is manufactured on a 0.18 μm CMOS process and operatesfrom 1.8 V and 3.3 V supplies. It is enclosed in a 100-lead TQFPpackage.Product Highlights Low noise and intermodulation distortion (IMD) enable high quality synthesis of wideband signals from baseband to high intermediate frequencies. Proprietary DAC output switching technique enhances dynamic performance. CMOS data input interface with adjustable setup and hold. Low power complex 32-bit numerically controlled oscillators (NCOs).Applications Wireless infrastructure W-CDMA, CDMA2000, TD-SCDMA, WiMAX, GSM Digital high or low IF synthesis Transmit diversity Wideband communications LMDS/MMDS, point-to-point

The ADA4091-2 dual and ADA4091-4 quad are micropower,single-supply, 1.2 MHz bandwidth amplifiers featuring rail-torailinputs and outputs. They are guaranteed to operate from a+3.0 V to +30 V single supply as well as from ±1.5 V to ±15 Vdual supplies.The ADA4091-2 / ADA4091-4 features a unique input stage thatallows the input voltage to exceed either supply safely without anyphase reversal or latch-up; this is called overvoltage protection(OVP).Applications for these amplifiers include portable telecommunicationsequipment, power supply control and protection,and interface for transducers with wide output ranges. Sensorsrequiring a rail-to-rail input amplifier include Hall effect, piezoelectric,and resistive transducers.The ability to swing rail-to-rail at both the input and output enablesdesigners, for example, to build multistage filters in single-supplysystems and to maintain high signal-to-noise ratios (SNR).The ADA4091-2 / ADA4091-4 is specified over the extended industrialtemperature range of −40°C to +125°C. The ADA4091-2 /ADA4091-4 is part of the growing selection of 36 V, low poweroperational amplifiers from Analog Devices, Inc.,The ADA4091-2 is available in 8-lead, plastic SOIC and 8-leadLFCSP packages. The ADA4091-4 is available in 14–lead TSSOPand 16-lead LFCSP surface-mount packages.Applications Industrial process control Battery-powered instrumentation Power supply control and protection Telecommunications Remote sensors Low voltage strain gage amplifiers DAC output amplifiers

The ADA4505-1/ADA4505-2/ADA4505-4 are single, dual, and quad micropower amplifiers featuring rail-to-rail input and output swings while operating from a single 1.8 V to 5 V power supply or from dual ±0.9 V to ±2.5 V power supplies.Employing a new circuit technology, these low cost amplifiers offer zero input crossover distortion (excellent PSRR and CMRR performance) and very low bias current, while operating with a supply current of less than 10 μA per amplifier.This combination of features makes the ADA4505-x amplifiers ideal choices for battery-powered applications because they minimize errors due to power supply voltage variations over the lifetime of the battery and maintain high CMRR even for a rail-to-rail op amp.Remote battery-powered sensors, handheld instrumentation and consumer equipment, hazard detectors (for example, smoke, fire, and gas), and patient monitors can benefit from the features of the ADA4505-x amplifiers.The ADA4505-x family is specified for both the industrial temperature range (−40°C to +85°C) and the extended industrial temperature range (−40°C to +125°C). The ADA4505-1 single amplifier is available in a tiny 5-lead SOT-23. The ADA4505-2 dual amplifier is available in a standard 8-lead MSOP and a 8-ball WLCSP. The ADA4505-4 quad amplifier is available in a 14-lead TSSOP and a 14-ball WLCSP.The ADA4505-x family is a member of a growing series of zero crossover op amps offered by Analog Devices, Inc., including the AD8506/AD8508, which also operate from a single 1.8 V to 5 V power supply or from dual ±0.9 V to ±2.5 V power supplies.Applications Pressure and position sensors Remote security Medical monitors Battery-powered consumer equipment Hazard detectors

The ADA4817-1 (single) and ADA4817-2 (dual) FastFET™ amplifiers are unity-gain stable, ultrahigh speed, voltage feedback amplifiers with FET inputs. These amplifiers were developed with the Analog Devices, Inc., proprietary eXtra fast complementary bipolar (XFCB) process, which allows the amplifiers to achieve ultralow noise (4 nV/√Hz; 2.5 fA/√Hz) as well as very high input impedances.With 1.3 pF of input capacitance, low noise (4 nV/√Hz), low offset voltage (2 mV maximum), and 1050 MHz −3 dB bandwidth, the ADA4817-1/ADA4817-2 are ideal for data acquisition front ends as well as wideband transimpedance applications, such as photodiode preamps.With a wide supply voltage range from 5 V to 10 V and the ability to operate on either single or dual supplies, the ADA4817-1/ADA4817-2 are designed to work in a variety of applications including active filtering and analog-to-digital converter (ADC) driving. The ADA4817-1 is available in a 3 mm × 3 mm, 8-lead LFCSP and 8-lead SOIC, and the ADA4817-2 is available in a 4 mm × 4 mm, 16-lead LFCSP. These packages feature a low distortion pinout that improves second harmonic distortion and simplifies circuit board layout. They also feature an exposed pad that provides a low thermal resistance path to the printed circuit board (PCB). The EPAD enables more efficient heat transfer and increases reliability. These products are rated to work over the extended industrial temperature range (−40°C to +105°C).Applications Photodiode amplifiers Data acquisition front ends Instrumentation Filters ADC drivers Output buffers

The ADA4939-1 / ADA4939-2 are low noise, ultralow distortion,high speed differential amplifiers. They are an ideal choice fordriving high performance ADCs with resolutions up to 16 bitsfrom dc to 100 MHz. The output common-mode voltage is useradjustable by means of an internal common-mode feedback loop,allowing the ADA4939-1 / ADA4939-2 output to match the inputof the ADC. The internal feedback loop also provides exceptionaloutput balance as well as suppression of even-order harmonicdistortion products.With the ADA4939-1 / ADA4939-2, differential gain configurationsare easily realized with a simple external feedback network of fourresistors that determine the closed-loop gain of the amplifier.The ADA4939-1 / ADA4939-2 are fabricated using Analog Devices,Inc., proprietary silicon-germanium (SiGe), complementary bipolarprocess, enabling them to achieve very low levels of distortion withan input voltage noise of only 2.3 nV/√Hz. The low dc offset andexcellent dynamic performance of the ADA4939-1 / ADA4939-2make them well suited for a wide variety of data acquisition andsignal processing applications.The ADA4939-1 (single) is available in a 3 mm × 3 mm, 16-leadLFCSP, and the ADA4939-2 (dual) is available in a 4 mm × 4 mm,24-lead LFCSP. The pinouts are optimized to facilitate printedcircuit board (PCB) layout and minimize distortion. TheADA4939-1/ADA4939-2 are specified to operate over the−40°C to +105°C temperature range; both operate on suppliesbetween 3.3 V and 5 V.Applications ADC drivers Single-ended-to-differential converters IF and baseband gain blocks Differential buffers Line drivers