160 MHz Rail-to-Rail Amplifier with Disable Features: Fully specified for +3 V, +5 V and ±5 V Supplies Output Swings Rail to Rail Input Voltage Range Extends 200 mV Below Ground No Phase Reversal with Inputs 1 V Beyond Supplies Disable/Power-Down Capability Low Power of 5.2 mA (26 mW on 5 V) High Speed and Fast Settling on 5 V: 160 MHz -3 dB Bandwidth (G = +2) 160 V/µs Slew Rate 30 ns Settling Time to 0.1% Good Video Specifications (RL = 150 Ω, G = +2) Gain Flatness of 0.1 dB to 30 MHz 0.03% Differential Gain Error 0.03° Differential Phase Error Low Distortion -69 dBc Worst Harmonic @ 10 MHz Outstanding Load Drive Capability Drives 50 mA 0.5 V from Supply Rails Cap Load Drive of 45 pF

Triple Differential Driver for Wideband Video Features:Triple high speed fully differential driver700 MHz, 3 dB, 2 V p-p bandwidth (AD8146/AD8148)600 MHz, 3 dB, 2 V p-p bandwidth (AD8147)200 MHz, 0.1 dB, 2 V p-p bandwidth3000 V/s slew rate Fixed gain (AD8146/AD8147: G = 2, AD8148: G = 4) Differential or single-ended input to differential output Can be used as differential-to-differential receiver Drives one or two 100 UTP cables Adjustable output common-mode voltage (AD8146) Internal common-mode feedback network Output balance error 50 dB @ 50 MHz On-chip, sync-on common-mode encoding (AD8147/AD8148) Output pull-down feature for line isolation Low power: 57 mA @ 5 V for 3 drivers (AD8146) Wide supply voltage range: +5 V to 5 V Available in a small 4 mm 4 mm LFCSP

Single-Supply, Low Cost Instrumentation Amplifier Features:Gain set with 1 resistor per amplifierGain = 5 to 1000InputsVoltage range to 150 mV below negative rail25 nA maximum input bias current30 nV/Hz, RTI noise @ 1 kHzPower suppliesDual supply: 2V to 12Single supply: 3V to 24V500 A maximum supply current

Single-Lead, Heart Rate Monitor Front End Features: Fully integrated single-lead ECG front end Low supply current: 170 μA (typical) Common-mode rejection ratio: 80 dB (dc to 60 Hz) Two or three electrode configurations High signal gain (G = 100) with dc blocking capabilities 2-pole adjustable high-pass filter Accepts up to ±300 mV of half cell potential Fast restore feature improves filter settling Uncommitted op amp 3-pole adjustable low-pass filter with adjustable gain Leads off detection: ac or dc options Integrated right leg drive (RLD) amplifier Single-supply operation: 2.0 V to 3.5 V Integrated reference buffer generates virtual ground Rail-to-rail output Internal RFI filter 8 kV HBM ESD rating Shutdown pin 20-lead 4 mm × 4 mm LFCSP package Qualified for automotive applications

10 MHz, G = 1, 10, 100, 1000 iCMOS Programmable Gain Instrumentation Amplifier Features: Small package: 10-lead MSOP Programmable gains: 1, 10, 100, 1000 Digital or pin-programmable gain setting Wide supply: ±5 V to ±15 V Excellent dc performance High CMRR: 100 dB (minimum), G = 100 Low gain drift: 10 ppm/°C (maximum) Low offset drift: 1.2 µV/°C (maximum), G = 1000 See data sheet for additional features

8-Channel, Low Noise, Low Power, 24-Bit, Sigma-Delta ADC with PGA and Reference Features: 3 power modes RMS noise Low power: 24 nV rms at 1.17 SPS, gain = 128 (255 µA typical) Mid power: 20 nV rms at 2.34 SPS, gain = 128 (355 µA typical) Full power: 23 nV rms at 9.4 SPS, gain = 128 (930 µA typical) Up to 22 noise free bits in all power modes (gain = 1) Output data rate Full power: 9.38 SPS to 19,200 SPS Mid power: 2.34 SPS to 4800 SPS Low power: 1.17 SPS to 2400 SPS Rail-to-rail analog inputs for gains > 1 Simultaneous 50 Hz/60 Hz rejection at 25 SPS (single cycle settling) Diagnostic functions (which aid safe integrity level (SIL) certification) Crosspoint multiplexed analog inputs 8 differential/15 pseudo differential inputs See data sheet for additional features

Pin-Programmable, Ultralow Noise, 24-Bit, Sigma-Delta ADC for Bridge Sensors Features:Pin-programmable output rateOutput data rate: 10 Hz, 50 Hz, 60 Hz, 120 HzPin-programmable PGAGain: 1, 8, 64, 128Pin-programmable power-down and resetRMS noise: 15 nV @ 10 Hz (gain = 128)Up to 21.5 noise free bits (gain = 1)Please see data sheet for additional features

Quad, 16-Bit, 2.4 GSPS, TxDAC+ Digital-to-Analog Converter Features: Supports input data rates up to 1 GSPS Proprietary, low spurious and distortion design Single carrier LTE 20 MHz bandwidth (BW), ACLR = 77 dBc at 180 MHz IF Six carrier GSM IMD = 78 dBc, 600 kHz carrier spacing at 180 MHz IF SFDR = 72 dBc at 180 MHz IF, −6 dBFS single tone Flexible 8-lane JESD204B interface Multiple chip synchronization Fixed latency Data generator latency compensation Input signal power detection High performance, low noise phase-locked loop (PLL) clock multiplier Digital inverse sinc filter Digital quadrature modulation using a numerically controlled oscillator (NCO) Nyquist band selection—mix mode Selectable 1×, 2×, 4×, and 8× interpolation filters Low power: 2.11 W at 1.6 GSPS, full operating conditions 88-lead, exposed pad LFCSP

MxFE Quad, 16-Bit, 12 GSPS RF DAC and Dual, 12-Bit, 6 GSPS RF ADC Features:Flexible reconfigurable common platform design 4 DACs and 2 ADCs (4D2A) and 2D2A options Supports single, dual, and quad band Datapaths and DSP blocks are fully bypassableDAC to ADC sample rate ratios of 1, 2, 3, and 4 On-chip PLL with multichip synchronization External RFCLK input option for off-chip PLL Maximum DAC sample rate up to 12 GSPS Maximum data rate up to 12 GSPS using JESD204C Useable analog bandwidth to 8 GHz Maximum ADC sample rate up to 6 GSPS Maximum data rate up to 6 GSPS using JESD204C Useable analog bandwidth to 8 GHz ADC ac performance at 6 GSPS, input at 2.7 GHz, 1 dBFS Full-scale input voltage: 1.475 V p-p Noise density: 147.5 dBFS/Hz Noise figure: 25.3 dB HD2: 72 dBFS HD3: 68 dBFS Worst other (excluding HD2 and HD3): 78 dBFS DAC ac performance at 12 GSPS, output at 2.6 GHz Full-scale output current range: 6.43 mA to 37.75 mA Two-tone IMD3 (6 dBFS per tone): 72 dBc NSD, single-tone: 160 dBc/Hz SFDR, single-tone: 75 dBc Versatile digital features Selectable interpolation and decimation filters Configurable DDC and DUC 8 fine complex DUCs and 4 coarse complex DUCs 8 fine complex DDCs and 4 coarse complex DDCs 48-bit NCO per DUC or DDC Option to bypass fine and coarse DUC/DDC Programmable 192-tap PFIR filter for receive equalization Supports 4 different profile settings loaded via GPIO Programable delay per data path Receive AGC support Fast detect with low latency for fast AGC control Signal monitor for slow AGC control Dedicated AGC support pins Transmit DPD support Fine DUC channel gain control and delay adjust Coarse DDC delay adjust for DPD observation path Auxiliary features Fast frequency hopping Direct digital synthesis (DDS) Low latency loopback modes (receive datapath data can be routed to the transmit datapaths) ADC clock driver with selectable divide ratios Power amplifier downstream protection circuitry On-chip temperature monitoring unit Flexible GPIO pins TDD power savings option SERDES JESD204B/JESD204C interface, 16 lanes up to 24.75 Gbps 8 lanes JESD204B/C transmitter (JT×) and 8 lanes JESD204B/C receiver (JR×) JESD204B compliance with the maximum 15.5 Gbps JESD204C compliance with the maximum 24.75 Gbps Supports real or complex digital data (8-, 12-, 16-, or 24-bit) 15 mm × 15 mm, 324-ball BGA with 0.8 mm pitch

8-Bit, 1 GSPS, JESD204B, Quad Analog-to-Digital Converter Features:JESD204B (Subclass 1 and Subclass 0) coded serial digital outputs Lane rates up to 15 Gbps 1.6 W total power at 1 GSPS 400 mW per ADC channel SFDR: 71 dBFS at 611 MHz (1.44 V p-p input range) SNR: 48.6 dBFS at 611 MHz (1.44 V p-p input range) SINAD: 48.5 dBFS at 611 MHz (1.44 V p-p input range) 0.9 V, 1.8 V, and 2.5 V dc supply operation No missing codes Internal ADC voltage reference Analog input buffer On-chip dithering to improve small signal linearityFlexible differential input range 1.44 V p-p to 2.16 V p-p (1.44 V p-p default) 1.4 GHz analog input full power bandwidth Fast detect bits for efficient AGC implementation Differential clock input Integer clock divide by 1, 2, 4, or 8 On-chip temperature diode Flexible JESD204B lane configurations